Adjusting a Redzone compound bow is a straightforward process, requiring only an Allen wrench and a feel for your desired weight. The bow's draw weight can be adjusted by loosening the limb locking screws and tightening or loosening the limb bolts. This simple mechanism allows archers to customise their bow to their individual needs, ensuring a smooth and controlled shooting experience.
The riser is the central part of the bow that connects the limbs and other mechanical components. It is supposed to be strong and light but not flexible. It is usually made of aluminium or carbon fibre to reduce the weight of the compound bow.
To locate the limb bolts, look for the large circular knobs near the centre of your bow. These knobs attach the bow's arms to the riser, and inside them, you will find the limb bolts. Once you have located the limb bolts, you can use an Allen wrench to adjust the draw weight of your bow.
It is important to note that some bows have limb bolts covered with limb pockets or caps that need to be removed first. So, if your bow has limb pockets or caps, be sure to remove them before attempting to adjust the limb bolts.
You may want to see also
To loosen the limb locking screws of a compound bow, you will need an Allen wrench. The size of the Allen wrench depends on the model of your compound bow, but it is usually a 3/16 size and is often included with the bow.
The limb locking screws can be found on either side of the limb bolts, which are located near the centre of your compound bow. They can be undone with the same Allen wrench used to adjust the limb bolts, or they may require a separate screwdriver.
It is important to note that you should not over-tighten the limb bolts as this could cause the bowstring or cams to break. You should also consult your bow's manual to find out how many times the limb bolts can be safely turned in either direction. Finally, make sure to secure the locking screws once you have finished adjusting your compound bow to prevent the limb bolts from disengaging, which can be dangerous.
You may want to see also
To adjust a compound bow's draw weight, you must tighten or loosen the limb bolts. These bolts are located near the centre of your compound bow and attach the bow's arms to the riser. To adjust them, you will need an Allen wrench.
Before you begin, loosen the limb locking screws. These are usually found on either side of the limb bolts and can be loosened with the same Allen wrench.
Now, insert the short arm of the Allen wrench into the bolt and turn it either clockwise to tighten or counterclockwise to loosen. Adjust the tension of each arm of the bow to your preferred weight. Ensure that you turn each bolt the same amount to keep the bow in tune.
On most compound bows, one rotation of the limb bolt translates to roughly a pound and a half of weight. Therefore, it is recommended to tighten or loosen the bolts one full rotation at a time to help you keep track of the tension level.
Once you have finished adjusting, secure the limb locking screws and test the bow's pull. Hold the bow as you usually would and pull back the bowstring. If you are satisfied with the draw weight, you are done. If not, continue adjusting until you get it how you want it.
You may want to see also
Choose the Right Day for Testing:
It is important to ensure your muscles are well-rested before testing the bow's pull. Avoid any strenuous activities in the 24 hours leading up to the test, including upper body exercises, heavy lifting, or endurance exercises. Additionally, get a good night's sleep and ensure you haven't had any muscle strains in the past three days.
Prepare Your Gear:
You will need a way to simulate the draw weight of your bow. If you already have a bow, you can use that. Alternatively, you can use resistance bands to mimic the desired draw weight. Measure the standard draw weight by pulling the bands back to 28 inches and using a bow scale or a luggage scale to measure the weight. Protect your fingers during this process, either with a tab or a thick sock, as you will be holding the string for an extended period.
Take the Test:
Stand with your feet at shoulder width, just as you would when drawing a bow. Raise your arm and draw the band/string to your normal anchor point. Hold this pose for 40 seconds. Take a break for up to 90 seconds, then repeat the process. Continue doing this until you can no longer pull the bow/resistance band. This is an endurance test, so push yourself, but be mindful of your body's limits.
Analyze the Results:
The number of repetitions you were able to complete during the test will help you determine if the chosen draw weight is right for you. If you were able to complete 15 repetitions or more, the draw weight might be too light, and you could consider increasing the poundage. If you couldn't reach 9 repetitions, the draw weight is likely too heavy, and you should consider decreasing it.
Retest if Necessary:
If the draw weight was too heavy or too light, adjust the poundage accordingly and retest. For example, if the previous weight was 30 lbs and felt too heavy, you could decrease it by 30% to 21 lbs for the next test. Conversely, if it felt too light, you could increase it by 10% to 33 lbs.
Remember, the goal is to find a draw weight that feels comfortable and allows you to maintain good form and accuracy. It's better to start with a lighter draw weight, especially if you're a beginner, as shooting with a too-heavy bow can lead to issues like shaking, poor form, and even muscle strain or injury.
You may want to see also
The draw length of a compound bow is critical to shooting effectively and maintaining proper form. A draw length that is even an inch too long or too short can cause issues ranging from a lack of accuracy to damage. It is important to adjust the draw length to suit your body type and measurements.
Finding Your Draw Length
To find your draw length, you must first measure your arm span. Stand with your arms spread out in a T-shape and ask an assistant to measure the distance between the tips of your middle fingers. Once you have this number, divide it by 2.5 to get your approximate draw length.
Types of Modules
The draw length of a compound bow is typically controlled by modules attached to the cams. There are two primary methods for adjusting draw length: replaceable modules and adjustable modules.
#### Replaceable Modules
Many high-end bows come with replaceable modules. To change the draw length, you must uninstall and reinstall the current module. Each draw length will have its own module, and you can refer to the instruction manual or the manufacturer's website to determine which module to use. You may need to use a bow press if the wires rest on the module.
#### Adjustable Modules
Some compound bows have adjustable modules with a system of markings or holes that correspond to specific draw length distances. You can adjust the draw length by unscrewing the module, twisting it to the desired length, and then reattaching the screws.
Adjusting the Draw Length
Once you have determined your draw length and understood the type of modules you have, you can adjust your bow to that length. If your cams and modules are not replaceable, you can adjust them according to the codes, numbers, or instruction manual. Compound bows are usually labelled with letters or numbers that indicate different draw lengths.
Fine-Tuning Your Draw Length
After adjusting your bow to your estimated draw length, you may find that it still feels too short or too long. In this case, you can fine-tune the draw length by adding or removing twists from the bowstring. Most compound bows can be configured on one-inch intervals, but more experienced archers may desire greater flexibility. To achieve this, you will need to use a bow press to untangle the string and cables before adding or removing twists.
Precautions
When adjusting the draw length on your compound bow, be sure not to overtighten the limb bolts, as this can cause strain on the bowstring or cam. It is also important to tighten the locking screws when you are finished to prevent the limb from disengaging during use, which could be dangerous.
You may want to see also
